An independent reference about small hand repairs to clothes. Not a shop or an atelier, sells nothing, and is not connected with any brands, shops or the former website on this domain.

Guides

Practical guides

The first article in this section is about hemming trousers by hand, because this job comes up more often than any other: trousers are often a little long from the start, and over time the hem comes down from rubbing against shoes. A blind stitch holds the hem securely and is almost invisible from the right side. Below you will find the order of work with examples, typical mistakes and a short checklist for your result.

A blind stitch does not like haste or tight thread. Catch literally one or two threads of the outer fabric and do not pull the stitch tight: let the thread lie loosely, and no dimples or puckers will appear on the right side.

— A note from the sewing box

What to prepare

  • Trousers, washed and ironed, so the length does not change after the first wash.
  • The shoes you will wear with the trousers most often.
  • A fine needle and thread matching the fabric or slightly darker.
  • Pins, tailor's chalk or a thin sliver of soap, and small scissors.
  • A thimble for the middle finger of your sewing hand.
  • An iron and an ironing board for pressing the hem.
  1. Mark the length

    Put the trousers on with the right shoes and fold the edge inwards to the length you want. Ask someone to pin the hem at the front and back, or do it yourself in front of a mirror, standing straight.

    For example: at the front the hem just touches the top of the shoe, and at the back it covers the top of the heel without reaching the floor.

  2. Transfer the line with chalk

    Take the trousers off, turn them inside out and chalk the fold line along the pins all the way round the leg. Compare both legs by folding the trousers along the creases: the lines should match.

    For example: if the line on one leg has drifted lower, level it with the other, otherwise the difference will show when you walk.

  3. Trim the allowance

    Measure a hem allowance of about two fingers' width from the fold line and cut off the excess. Overcast the raw edge so it does not fray.

    For example: dense wool hardly frays at the cut edge, but loose linen without overcasting will start to fray after the very first wash.

  4. Fold and pin the hem

    Fold the edge up along the chalk line, line up the side seams of the leg and the hem, and pin across. Press the fold with an iron through a damp cloth so it holds its shape.

    For example: if the side seams do not match, the hem will twist and the bottom of the leg will stick out at an angle.

  5. Secure the thread

    Thread a single strand, tie a knot and hide it inside the hem, bringing the needle out right at the fold. That way the knot shows neither on the right side nor on the inside.

    For example: start at the inner side seam, where the first stitches are easiest to hide.

  6. Sew with a blind stitch

    Catch one or two threads of the trouser leg, then run the needle a short way inside the fold of the hem and bring it out again. Repeat all the way round without pulling the thread tight.

    For example: if a dot shows on the right side, catch even less, literally a single thread.

  7. Fasten off

    When you get back to the start, make a few short stitches in one place inside the hem, pass the needle under them and draw the thread along the fold. Cut it close to the fabric.

    For example: fastening off on the side seam lasts longer, because there are more layers under the needle there.

  8. Press and check

    Remove the pins, press the hem through a damp cloth from the wrong side and put the trousers on. Look at the edge in daylight, from the side and while moving.

    For example: if the hem pulls in one place, unpick a couple of stitches and make them a little looser.

Common mistakes

  • Marking the length without shoes: the trousers end up shorter than you wanted.
  • Pulling the thread tight: dimples and ridges appear on the right side.
  • Catching too much fabric on the right side: the stitches become visible.
  • Sewing with doubled thread: the hem turns out stiff and lumpy.
  • Not lining up the side seams when folding the hem.
  • Pressing the hem on the right side without a cloth: wool is left with a shine.

If that does not work

  • If the fabric is very fine or slippery, first hold the hem with large tacking stitches, then sew with a blind stitch and pull the tacking out.
  • If the hem is on jeans, a hand blind stitch does not hold well: such an edge is easier to topstitch on a sewing machine, if you have one, or to take to a tailor.
  • If the trousers need shortening only a little, it is sometimes enough to unpick the old hem and fold it again along the new line.
  • If the trousers have turn-ups or a lining, it is better to go to a tailor: the order of work there is more complicated.

Check your work against the list

  • The length is marked in the shoes the trousers will be worn with.
  • Both legs are the same length after marking.
  • The raw edge of the allowance is overcast and does not fray.
  • The side seams of the leg and the hem line up.
  • The knot and the fastening-off are hidden inside the hem.
  • No stitches show on the right side in daylight.
  • The hem does not pull or pucker after pressing.

Catalogue of articles for English-language readers

This is where standalone articles on small hand repairs will appear, written for English-speaking readers: mending seams in different fabrics, taking up hems, closing small holes and sewing small fastenings back in place. Each article is tried out on ordinary clothes before it goes into the catalogue.

Coming soon

  • Darning a worn heel on a wool sock so the repair stays soft underfoot.
  • Taking up the hem of a lightweight summer dress without the edge pulling or showing through.
  • A patch on the wrong side for the worn knee of children's jeans: fabric, shape and stitch.
  • Sewing a sturdy hanging loop into a heavy winter coat so it carries the weight.
  • A split seam in a jacket lining: what you can mend yourself and what to leave to a tailor.

Editorial rules

  • Articles in this catalogue are written separately for each language version and are not translations.
  • Some articles link to third-party websites, including gaming services; we do not control their content, prices or terms.
  • We do not sell fabric, thread or haberdashery and we do not take sewing orders; we do not publish advertising, rankings, prices or reviews.
  • Sections

    A map of topics: kit and preparation, stitches, seams and hems, holes and small fastenings.

  • Reference

    A glossary of tools, stitches and fabric properties, from the thimble to the lengthwise grain and bias.

  • Questions

    Short answers about thread and needles, seams and hems, holes, hanging loops and stuck zips.

  • Collections

    Reading lists: a travel mending kit, children's clothes, knitwear without puckered seams.

What we relied on

  • The care label on your garment
  • Editorial notes of this reference

The methods in this reference are meant for ordinary everyday clothes: cotton, linen, denim, suiting wool and firm knitwear. Fine, slippery and loosely woven fabrics behave in their own way, so try any unfamiliar stitch on a seam allowance or a spare scrap first, and follow the garment's care label when washing and ironing after a repair.